Inspection Procedure
- CHECK FUSE (RR-IG1-3, D S/HTR, D-IG1-3)
- Remove the RR-IG1-3 fuse from the luggage room junction block.
- Remove the D S/HTR and D-IG1-3 fuses from the main body ECU.
- Measure the resistance of the fuses.
Standard resistance
TESTER CONNECTOR SPECIFIED CONDITION CHARTTester Connector Condition Specified Condition RR-IG1-3 fuse Always Below 1 Ω D S/HTR fuse Always Below 1 Ω D-IG1-3 fuse Always Below 1 Ω NG: REPLACE FUSE
OK: Go to next step
- CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL ECU - BATTERY AND BODY GROUND)
- Disconnect the e34 ECU connector.
- Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTOR SPECIFIED CONDITION CHARTTester Connector Condition Specified Condition e34-12 (GND) - Body ground Always Below 1 Ω - Measure the voltage of the wire harness side connector.
Standard voltage
TESTER CONNECTOR SPECIFIED CONDITION CHARTTester Connector Switch Condition Specified Condition e34-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V e34-2 (SYSB) - Body ground Always 11 to 14 V NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
- CHECK HARNESS AND CONNECTOR (SEAT CLIMATE SWITCH LH - BATTERY AND BODY GROUND)
- Disconnect the L67 switch connector.
- Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTOR SPECIFIED CONDITION CHARTTester Connector Condition Specified Condition L67-2 (E) - Body ground Always Below 1 Ω - Measure the voltage of the wire harness side connector.
Standard voltage
TESTER CONNECTOR SPECIFIED CONDITION CHARTTester Connector Switch Condition Specified Condition L67-7 (IG) - Body ground Engine switch on (IG) 11 to 14 V NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
- INSPECT CLIMATE CONTROL SWITCH LH
- Remove the L67 switch connector.
- Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTOR SPECIFIED CONDITION CHARTTester Connector Switch Condition Specified Condition 5 (V5L) - 4 (VSL) Cooler MAX → Heater MAX Below 1 Ω → 5 kΩ Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NG: REPLACE CLIMATE CONTROL SWITCH LH (See REMOVAL )
OK: Go to next step
- CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL ECU - SEAT CLIMATE SWITCH LH AND BODY GROUND)
- Disconnect the e34 ECU connector.
- Disconnect the L67 switch connector.
- Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTOR SPECIFIED CONDITION CHARTTester Connector Condition Specified Condition e34-14 (V5) - L67-5 (V5L) Always Below 1 Ω e34-18 (VS) - L67-4 (VSL) Always Below 1 Ω e34-15 (VG) - L67-3 (VGL) Always Below 1 Ω e34-14 (VS) - Body ground Always 10 kΩ or higher e34-18 (VS) - Body ground Always 10 kΩ or higher e34-15 (VG) - Body ground Always 10 kΩ or higher Fig 4: Checking Harness And Connector (Seat Climate Control ECU - Seat Climate Switch LH And Body Ground)Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE SEAT CLIMATE CONTROL ECU (See DISASSEMBLY )